Quantcast
Viewing all 9484 articles
Browse latest View live

AXIS P8221 Network I/O Audio Module, version 5.10

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.10
================
5.10 is the first official release for the AXIS P8221.

AXIS P1311 Network Camera, version 5.01.2

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.01.2
================

Improvements in 5.01.2 since 5.01.1
================
5.01.2:I01 Added support for a new internal memory type.

AXIS M1011 Network Camera, version 5.20.1

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.20.1
================

Corrections in 5.20.1 since 5.20
================
5.20.1:C01 Solved problem with video is streamed at a higher framerate than specified.

5.20.1:C02 RTP over RTSP over HTTP issue is solved.

5.20.1:C03 Corrected problem with AVHS One-click.

5.20.1:C04 Now Image appearance settings are restored when using "Restore" function.

5.20.1:C05 ONVIF setup/configuration issue is solved.

AXIS Q7406 Video Encoder, version 5.11.1

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.11.1
================

New features in 5.11.1 since 5.11
================
5.11.1:F01 SPS/PPS data available in the H264 stream.

5.11.1:F02 Multicast traffic VLAN tagged if AllowClientTransportSettings=yes.

Corrections
================
5.11.1:C01 Behaviour of videostatus.cgi.

AXIS M3011 Network Camera, version 5.21

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.21
================

New features
================
5.21:F01 Added embedded AVHS (Axis Video Hosting System) client.

5.21:F02 Added ONVIF (Open Network Video Interface Forum) support including
metadata streaming over RTSP/RTP. This includes streaming of event
data, PTZ position and status data, and analytics data. Dynamic web
services discovery protocol as specified in ONVIF standard, which
follows WS-Discovery definitions (remote discovery will not be
supported), is also included.


5.21:F03 Added support for 802.1x.

5.21:F04 Functionality has been added making it possible for customer to upload
a customer logotype in the live view webpage.

Corrections
================
5.21:C01 It is possible now to see rotated image at the Motion detection
and exposure settings page.

AXIS Q7404 Video Encoder, version 5.20

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

New Features
================
5.20:F01 Added embedded AVHS (Axis Video Hosting System) client.

5.20:F02 Added ONVIF (Open Network Video Interface Forum) support including
metadata streaming over RTSP/RTP. This includes streaming of event
data, PTZ position and status data, and analytics data. Dynamic web
services discovery protocol as specified in ONVIF standard, which
follows WS-Discovery definitions (remote discovery will not be
supported), is also included.

5.20:F03 Axis Camera Application Platform (ACAP) enabling third party
developers (ADP partners) to develop, download and run their
applications on Axis products is included.

5.20:F04 Added support for Generic TCP/IP over DaisyChain.

5.20:F05 Added AudioClips functionality.

Corrections since 5.02
================
5.20:C01 It is possible now to see rotated image at the Motion detection
and exposure settings page.

5.20:C03 Fixed issue with sftpclient.

5.20:C04 Now it works fine with serial generic TCP timeoout.

5.20:C05 Issue with RTP over RTSP over HTTP problem is fixed.

5.20:C07 Solved issue with Axis Metadata monitor.

5.20:C08 Incorrect RTP timestamping of the SPS/PPS frames issue is fixed.

5.20:C09 Included fix for stability.

5.20:C10 RTSP SETUP fails fix is included.

5.20:C11 No problem now to upload Language file.

AXIS M7001 Video Encoder, version 5.20

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

New Features
================
5.20:F01 Added embedded AVHS (Axis Video Hosting System) client.

5.20:F02 Added ONVIF (Open Network Video Interface Forum) support including
metadata streaming over RTSP/RTP. This includes streaming of event
data, PTZ position and status data, and analytics data. Dynamic web
services discovery protocol as specified in ONVIF standard, which
follows WS-Discovery definitions (remote discovery will not be
supported), is also included.

5.20:F03 Added support for 802.1x.

5.20:F04 Functionality has been added making it possible for customer to upload
a customer logotype in the live view webpage.

Corrections since 5.02
================
5.20:C01 It is possible now to see rotated image at the Motion detection
and exposure settings page.

5.20:C02 Dynamic Text Overlay works now as intended.

5.20:C03 Solved issue with time in the overlay should be the same as the NTP time.

5.20:C04 Overlay Image Upload is enabled.

5.20:C05 Fixed issue with sftpclient.

5.20:C06 Issue with RTP over RTSP over HTTP problem is fixed.

5.20:C07 Solved issue with Axis Metadata monitor.

5.20:C08 Incorrect RTP timestamping of the SPS/PPS frames issue is fixed.

5.20:C9 Included stability fix.

AXIS Q7414 Video Encoder Blade, version 5.25

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.25
================
5.25 is the first official release for the AXIS Q7414.

Added features
================

AXIS T8412 Installation Display, version T8412-6-724-937

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE T8412-6-724-937
================
Improvements in T8412-6-724-937 since T8412-6-724-931

Im01: Improved support for ONVIF.

RELEASE T8412-6-724-931
================
Improvements in T8412-6-724-931 since T8412-6-724-759

Im01: Added support for ONVIF.
Im02: Now using VAPIX for improved detection of camera capabilites.
IM03: Added bandwidth calculator in video image.
IM04: Added display of MAC address and Hostname.
IM05: Added advanced scripting tool for direct setting of camera parameters, including enabling AVHS.
IM06: Added custom connect delay for network search.
IM07: Improved PTZ control.

Corrections in T8412-6-724-931 since T8412-6-724-759

C01: Fixed illegal subnet bug.
C02: Fixed issue with max frame size.

RELEASE T8412-6-724-759
================
Improvements in T8412-6-724-759 since T8412-6-724-758

Im01: Added support for class B subnets.

RELEASE T8412-6-724-758
================
Improvements in T8412-6-724-758 since T8412-6-724-748

Im01: Added support for using HTTP ports other than port 80.
Im02: Improved performance when connecting to cameras over LAN.
IM03: Added support for multi-port video encoders, including preview of video sources.


Corrections in T8412-6-724-758 since T8412-6-724-748

C01: Fixed entry of symbols in usernames and passwords.
C02: Corrected display of features per camera model.

AXIS M1031-W Network Camera, version 5.20.3

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.20.3
================

Corrections in 5.20.3 since 5.20.2
================
5.20.3:C01 Updated firmware revision for wireless module.
5.20.3:C02 Corrected an issue with some SMTP servers like GMX regarding the "From" address.
5.20.3:C03 Correction of IP address filter issue.

AXIS M1011-W Network Camera, version 5.20.2

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.20.2
================

Corrections in 5.20.2 since 5.20.1
================
5.20.2:C01 Updated firmware revision for wireless module.
5.20.2:C02 Corrected an issue with some SMTP servers like GMX regarding the "From" address.
5.20.2:C03 Correction of IP address filter issue.

AXIS Q7401 Video Encoder, version 5.20.3

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Corrections since 5.20.2
================
5.20.3:C01 Solved an issue with the Generic TCP server.

New Features
================
5.20.3:F01 Support for a new type of NAND flash.

AXIS P7701 Network Video Decoder, version 5.07.4

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.07.4
================
5.07.4 is a production service release for AXIS P7701.

Corrections since 5.07.3
================
5.07.4:C01 Accept the "!" character in the password

5.07.4:C02 Corrected video stream continuity when switching between video sources

5.07.4:C03 Corrected a video issue when decoding high bitrate MJPEG over RTSP videostreams

AXIS Q1910 Thermal Network Camera, version 5.11.1

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

New Features
================
None

Corrections since 5.11
================
5.11.1:C01 Changed firmware configuration for flash memory
5.11.1:C02 Corrected formatting of Server Report

AXIS P5512-E PTZ Dome Network Camera, version 5.25.1

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.25.1
================
5.25.1 is a production service release for AXIS P5512-E.

Corrections in 5.25.1 since 5.25
================
5.25.1:C01 Corrected the SSP/PPS H264 parameters time stamps,
now it will be the same as the following I-frame.

5.25.1:C02 Socket leak during Guard Tour which caused
the camera to slow down.

5.25.1:C03 Ethernet driver and streaming fixes added,
should correct some cases where the camera was left unresponsive.

Known Bugs/Limitations
================
5.25.1:L01 Motion detection reacts to IR cut filter switching.

5.25.1:L02 Uploading an expired or not yet valid encrypted client certificate in PKCS#12 format for 802.1x will succeed instead of being rejected as it should be.

5.25.1:L03 RTSP clients timeout when syncing unit to computer time due to the keepalive messages being regarded as too old/new depending on the time set.

5.25.1:L04 Errors in log when removing micro SD card without unmounting it first.

5.25.1:L05 Focus can sometimes be poor on the ELMO 401C block.

5.25.1:L06 Criticals found in system log at restart when Guard tour is running.

5.25.1:L07 Control panel is hidden behind the video sometimes. The AMC component is uncontrollable by the web viewer.

5.25.1:L08 After a factory default,the default PTZ home position not defined when the PTZ framework is told to go to the home position; the the camera will remain at the calibration point.

5.25.1:L09 Onvif failing test case 6.2.24. This is due to a bug in the test tool and test specification, i.e. the Axis interpretation is correct.

5.25.1:L10 No warning message in log when pre-trigger buffer is too large.

5.25.1:L11 ONVIF speed param is ignored by the camera.

5.25.1:L12 MJPG recordings to SD card with too high bitrate may cause oom kill of monolith. Lower the bitrate to a rate that the SD card/controller can handle. Can not give specifics since it differs between SD cards.

5.25.1:L13 From time and duration not respected in continuous recording <5 min; Cue points not available and seeking is not possible until a MKV-file is finalized (stopped or full 5 minutes).

AXIS P7224 Network Camera, version 5.40.7

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.40.7
================
5.40.7 is the first official production release for the AXIS P7224

Known Bug/Limitations
================
5.40.7:L1
Missing recording functionality over network share for products with no SD-card support.

5.40.7:L2
802.1x does not work in a Q7900 rack if a blade is placed in any of the rack positions 1, 5, 8, 11

5.40.7:L3
The 'Any' event does not work when triggered with the virtualinput.cgi

5.40.7:L4
It's not possible to get an event due to power-supply failure in a Q7900 rack

5.40.7:L5
Parameter PTZ.CamPorts.Cam#Port shall be -1 when no PTZ driver is installed, However on multi channel products the value is always > 0 for all
but the first channel.

5.40.7:L6
ptz.cgi returns unexpected values when no driver is installed on multi channel products

5.40.7:L7
AVHS radio button not enabled after enable and save

5.40.7:L8
In an AVHS installation, the clock is not synchronized with the AVHS server which may lead to incorrectly scheduled recordings.

5.40.7:L9
ONVIF discovery source address is not correct. The link local address is used as a source address, this is not according to RFC 3927
(section 2.7):

5.40.7:L10
When using the H.264 rate controller with a low GOV length (e.g. 3) you can get disrupted video. Use GOV length > 10.

5.40.7:L11
Network lost trigger is not available in Action rule setup.

5.40.7:L12
TCP notify in an Action rule doesn't work as expected.

5.40.7:L13
When action rules run, the name of the rule will sometimes be incorrectly logged in the system log.

5.40.7:L14
The center mode for click-in-picture doesn't work for ptz-control when using loadable drivers.

5.40.7:L15
The sound level is very high when there is no audio source connected. If the high-pass filter in the audio codec is enabled the level will
be low.

5.40.7:L16 Invalid multicast address in SDP content.

5.40.7:L17 90 and 270 rotation can cause a drop in frame rate.

Group Exceptions
================
General
Image and Video
PTZ Set PTZ parameters (ptzparam.cgi)
Motion Detection
I/O
Serial port
IP filter
Audio


Built in templates for dynamic parameters are:

Template Group
================
'audioclipaction' Event.E#.Actions
'button' PTZ.Auxiliary.A1.Button
'event' Event
'ftp_config' EventServers.FTP
'ftpaction' Event.E#.Actions
'guardtour' GuardTour
'guardtouraction' Event.E#.Actions
'http_config' EventServers.HTTP
'httpaction' Event.E#.Actions
'hwaction' Event.E#.Actions
'mediaclip' MediaClip
'motion' Motion
'ptzaction' Event.E#.Actions
'ptzsensoraction' Event.E#.Actions
'smtpaction' Event.E#.Actions
'streamcache' StreamCache
'streamprofile' StreamProfile
'tcp_config' Eventservers.TCP
'tcpaction' Event.E#.Actions
'tour' GuardTour.G#.Tour
'user_ctlqueue' PTZ.UserCtlQueue


Supported AXIS VAPIX API Image Resolutions for AXIS P7224.

AXIS P5512 PTZ Dome Network Camera, version 5.25.1

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.25.1
================
5.25.1 is a production service release for AXIS P5512.

Corrections in 5.25.1 since 5.25
================
5.25.1:C01 Corrected the SSP/PPS H264 parameters time stamps,
now it will be the same as the following I-frame.

5.25.1:C02 Socket leak during Guard Tour which caused
the camera to slow down.

5.25.1:C03 Ethernet driver and streaming fixes added,
should correct some cases where the camera was left unresponsive.

5.25.1:C04 Slow shutter exposure time is restored after reboot.

Known Bugs/Limitations
================
5.25.1:L01 Audio clip upload size limit, limited to less than ~1.5MB.

5.25.1:L02 Motion detection reacts to IR cut filter switching.

5.25.1:L03 Uploading an expired or not yet valid encrypted client certificate in PKCS#12 format for 802.1x will succeed instead of being rejected as it should be

5.25.1:L04 RTSP clients timeout when syncing unit to computer time due to the keepalive messages being regarded as too old/new depending on the time set.

5.25.1:L05 Cannot record audio clip with no wait time. You must wait at least 1 second.

5.25.1:L06 Errors in log when removing micro SD card without unmounting it first.

5.25.1:L07 Focus can sometimes be poor on the ELMO 401C block.

5.25.1:L08 Criticals found in system log at restart when Guard tour is running.

5.25.1:L09 Control panel is hidden behind the video sometimes. The AMC component is uncontrollable by the web viewer.

5.25.1:L10 After a factory default,the default PTZ home position not defined when the PTZ framework is told to go to the home position; the the camera will remain at the calibration point.

5.25.1:L11 Onvif failing test case 6.2.24. This is due to a bug in the test tool and test specification, i.e. the Axis interpretation is correct.

5.25.1:L12 No warning message in log when pre-trigger buffer is too large.

5.25.1:L13 ONVIF speed param is ignored by the camera.

5.25.1:L14 MJPG recordings to SD card with too high bitrate may cause oom kill of monolith. Lower the bitrate to a rate that the SD card/controller can handle. Can not give specifics since it differs between SD cards.

5.25.1:L15 From time and duration not respected in continuous recording <5 min; Cue points not available and seeking is not possible until a MKV-file is finalized (stopped or full 5 minutes).

AXIS P5522 PTZ Dome Network Camera, version 5.25.1

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.25.1
================
5.25.1 is a production service release for AXIS P5522.

Corrected problems
================
5.25.1:C01 Corrected the SSP/PPS H264 parameters time stamps,
now it will be the same as the following I-frame.

5.25.1:C02 Socket leak during Guard Tour which caused
the camera to slow down.

5.25.1:C03 Ethernet driver and streaming fixes added,
should correct some cases where the camera was left unresponsive.

5.25.1:C04 LLDP broadcasts the proper MAC address.

5.25.1:C05 Improved SHTTP client.

5.25.1:C06 Center command with specified image height works properly.

AXIS P3367 Network Camera, version 5.40.3.2

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

New Features/Functionality
================
5.40.3:F1 Events can now be triggered based on a temperature sensor.

5.40.3:F2 Events can now be triggered based on "Network lost".

Corrections since 5.40.3.1
================
5.40.3:C29780 Fixed a connection problem with the AVHS client that could
lead to infinite reconnect loop and criticials in the system log.

5.40.3:C32251 AVHS proxy should now work.

5.40.3:C33336 Fixed a performance problem with AVHS when using HTTPS.

5.40.3:C30984 Mute setting for Audio input gain is now working.

5.40.3:C31728 Administrators other than root can now configure ACAP
applications.

5.40.3:C32489 Fixed a problem with RTP tunneled over RTSP and HTTP that could
lead to terminated RTP sessions because of corrupt payload data.

5.40.3:C32529 Fixed a problem with UPnP NAT traversal that lead to NAT
traversal not working with several router brands.

5.40.3:C33232 Modifier #t for event notifications should now work as expected.

5.40.3:C33439 Fixed a problem with scheduled events not triggering at correct
time.

5.40.3:C33603 Fixed a problem with AVHS "always" register method.

5.40.3:C33603 Fixed a problem with the VAPIX I/O interface.

5.40.3:C33307 Fixed a problem with apps/focusd restarting and generating
critical log messages.

Known Bug/Limitations
================
5.40.3:L18122 Removing and reinserting SD card during recording is not
recommendable.

5.40.3:L10049 With audio enabled, the initial connection latency is increased.

5.40.3:L24316 Check and repair is only available if the file system is ext4.

5.40.3:L29580 A combination of a high bandwidth continuous recording and a lot
of small recordings can result in disc full. The automatic clean up will stop
at that point and the user has to manually remove recordings.

5.40.3:L28297 If you set max gain to a low value, e.g. 0, the IR cut filter
may not switch back on automatically.

5.40.3:L27901 Using modifiers like %c in a network share upload event does not
work.

5.40.3:L29056 Local recording playback fails when using Motion JPEG + audio
with resolution 2048x1536 and higher. Use H.264 instead.

5.40.3:L27653 Multiple simultaneous recordings to SD cards and network shares
can degrade the performance of the system.

5.40.3:L24975 90 and 270 rotation can cause a drop in frame rate.

AXIS P5522-E PTZ Dome Network Camera, version 5.25.1

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

RELEASE 5.25.1
================
5.25.1 is a production service release for AXIS P5522-E.

Corrected problems
================
5.25.1:C01 Corrected the SSP/PPS H264 parameters time stamps,
now it will be the same as the following I-frame.
5.25.1:C02 Socket leak during Guard Tour which caused
the camera to slow down.
5.25.1:C03 Ethernet driver and streaming fixes added,
should correct some cases where the camera was left unresponsive.
5.25.1:C04 LLDP broadcasts the proper MAC address.
5.25.1:C05 Improved SHTTP client.
5.25.1:C06 Center command with specified imageheight works properly.
Viewing all 9484 articles
Browse latest View live