Axis Communications Firmware

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

New features in 10.3.1
================================================================================

10.3.1:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.

10.3.1:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.

10.3.1:F3
Added support for the upcoming SE051 chip.

10.3.1:F4
On screen control config available in Server Report

10.3.1:F5
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.

10.3.1:F6
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.

10.3.1:F7
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.

10.3.1:F8
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.

10.3.1:F9
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).

10.3.1:F10
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.

10.3.1:F11
Corrected an issue that caused the audio transfer over HTTPS to not work
properly and with that, the audio-gain-level behavior was also reverted back to
the state it was known in AXIS OS releases up to AXIS OS 10.0.2. It is therefore
mandatory to upgrade to AXIS OS 10.3 when experiencing audio-related issues on
Axis devices running on AXIS OS 10.1 and 10.2. Upon release of AXIS OS 10.3,
AXIS OS 10.1 and 10.2 will be made unavailable for download from www.axis.com
moving forward.

10.3.1:F12
Refactoring of legacy text overlay to support new video provider

Corrections in 10.3.1
================================================================================

10.3.1:C1
Added missing help text sections.

10.3.1:C2
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.

10.3.1:C3
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.

10.3.1:C4
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.

10.3.1:C5
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.

10.3.1:C6
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel
scenarios.

10.3.1:C7
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.

10.3.1:C8
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

When updating the device from the A1601 Active track, it is important to
factory default the device together with the firmware upgrade due to fundamental
arcitectural differences in the access control engine.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

New features in 10.1.0.1
================================================================================

10.1.0:F1
First release of firmware on the Secure entry firmware track for compatibility
with AXIS Camera Station. Note that this firmware only works with AXIS Camera
Station and not partner solutions.

Limitations in 10.1.0.1
================================================================================

10.1.0.1:L1
If using action rules in AXIS Camera Staion to trigger on "Door held" in one of
the beta releases of AXIS Camera Station Secure Entry, this rule needs to be
reconfigured as the trigger name has changed to "Door open too long".

10.1.0.1:L2
Action rule in AXIS Camera Station with triggger on "Door Locked" after "Access
request" doesn't work.

10.1.0.1:L3
If a credential with access is swiped on a door in scheduled unlock, an
erronious "Access not taken"-event will be sent for the last credential swiped
with access before the end of the unlocking schedule.

10.1.0.1:L4
"Pre-alarm warning" is a selectable filter for Action rules in AXIS Camera Station,
even though the trigger will never happen.

10.1.0.1:L5
Setting the time from AXIS Camera Station doesn't update the device web interface.
but the time in the firmware is still set correctly.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue that sometimes prevented adjustment of the focus window.

9.80.3:C04
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C05
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C06
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 6.55 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 6.55 => 8.40 LTS => 9.80 LTS.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.5
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C03
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

(LLDP) in addition to PoE-class based power allocation. This allows the switch
to allocate less power to the camera and potentially a greater number of PoE
devices can be connected to the switch.
LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP POE
-> LLDP Send Max PoE.

9.80.2.5:F36
Added support for signed ACAP applications.

9.80.2.5:F37
Firwmare Recovery will also rollback the previous state of applications (ACAPs)
now.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel scenarios.

9.80.3:C10
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel scenarios.

9.80.3:C10
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

AXIS P3255-LVE, version 10.3.1

AXIS P3248-LVE, version 10.3.0.1

AXIS P3248-LV, version 10.3.0.1

AXIS P3247-LVE, version 10.3.0.1

AXIS P3247-LV, version 10.3.0.1

AXIS P3245-LVE, version 10.3.0.1

AXIS A1601, version 10.1.0.1

AXIS Q6125-LE, version 9.80.3

AXIS Q3615, version 9.80.3

AXIS Q1942, version 9.80.3

AXIS Q1941-E, version 9.80.3

AXIS P9106-V, version 9.80.3

AXIS P3225-V_Mk_II, version 9.80.3

AXIS P3225-VE_Mk_II, version 9.80.3

AXIS P3224-V_Mk_II, version 9.80.3

AXIS P3224-VE_Mk_II, version 9.80.3

AXIS P1435-LE, version 9.80.3

AXIS P1435-E, version 9.80.3

AXIS P1364, version 9.80.3

AXIS P12_MkII, version 9.80.3