Axis Communications Firmware

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue that sometimes prevented adjustment of the focus window.

9.80.3:C04
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C05
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C06
Corrected an issue that prevented the device to utilize the available network bandwidth in
high-latency networks such as 4G cellular network.

9.80.3:C07
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C08
Corrected an issue with pause-frame handling that could cause network disconnections if
pause-frames were enabled and used in the network.

9.80.3:C09
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C10
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C11
Corrected an issue that caused video clients to not display a low-FPS video stream due to
missing base FPS info in VUI timing info.

9.80.3:C12
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C13
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel scenarios.

9.80.3:C14
Corrected an issue that could cause live image to blink in dark conditions on rare
occasions.

9.80.3:C15
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C07
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C08
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C07
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C08
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C07
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C08
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C07
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C08
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel scenarios.

9.80.3:C09
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel scenarios.

9.80.3:C10
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

If you need to step up your firmware several steps, it is recommended to do an
intermediate upgrade to LTS-tracks before proceeding.
For example if the current version is 7.40 and you want to upgrade to 9.80.
Then you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or at the firmware portal at
https://www.axis.com

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

Corrections in 9.80.3 since 9.80.2.4
=====================================

9.80.3:C01
General improvements to the LTS-2020 platform.

9.80.3:C02
Corrected an issue that sometimes could make it impossible to export the full length of
recordings.

9.80.3:C03
Corrected an issue in oak.cgi that could cause invalid requests.

9.80.3:C04
Update OpenSSL to version 1.1.1h to increase overall cyber security level.

9.80.3:C05
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail when certain
special characters were used as a password.

9.80.3:C06
Added support for dynamic power allocation via Link Layer Discovery Protocol (LLDP) in
addition to PoE-class based power allocation. This allows the switch to allocate less
power to the camera and potentially a greater number of PoE devices can be connected to
the switch. LLDP can be enabled in Settings -> System -> PlainConfig -> Network -> LLDP
POE -> LLDP Send Max PoE.

9.80.3:C07
Updated IANA Time Zone Database to version 2020d to get the latest Time Zone updates.

9.80.3:C08
Corrected an issue in the Web GUI that caused an error message when using a client
certificate with '>' character in it's ID for HTTPS access.

9.80.3:C09
Corrected an issue that caused the value of Quality of Service (QoS) to not be respected
in always multicast mode.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

New features in 10.3.0
================================================================================

10.3.0:F1
Axis Object Analytics 1.0.17 is preinstalled.

10.3.0:F2
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.

10.3.0:F3
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.

10.3.0:F4
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.

10.3.0:F5
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.

10.3.0:F6
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.

10.3.0:F7
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).

10.3.0:F8
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.

10.3.0:F9
Updated Video Motion Detection to version 4.4.9.

10.3.0:F10
Updated Motion Guard to version 2.2.8.

10.3.0:F11
Updated Fence Guard to version 2.2.8.

10.3.0:F12
Updated Loitering Guard to version 2.2.8.

Corrections in 10.3.0
================================================================================

10.3.0:C1
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.

10.3.0:C2
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.

10.3.0:C3
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.

10.3.0:C4
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.

10.3.0:C5
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.

10.3.0:C6
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.

10.3.0:C7
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

New features in 10.3.0
================================================================================

10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.

10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.

10.3.0:F3
Improved autofocus accuracy.

10.3.0:F4
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.

10.3.0:F5
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.

10.3.0:F6
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.

10.3.0:F7
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).

10.3.0:F8
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.

10.3.0:F9
Updated Video Motion Detection to version 4.4.9.

10.3.0:F10
Updated Motion Guard to version 2.2.8.

10.3.0:F11
Updated Fence Guard to version 2.2.8.

10.3.0:F12
Updated Loitering Guard to version 2.2.8.

Corrections in 10.3.0
================================================================================

10.3.0:C1
Corrected an issue that could cause live image to blink in dark conditions on
rare occasions.

10.3.0:C2
Added support for dynamic power allocation via Link Layer Discovery Protocol
(LLDP) in addition to PoE-class based power allocation. This allows the switch
to allocate less power to the camera and potentially a greater number of PoE
devices can be connected to the switch. LLDP can be enabled in Settings ->
System -> PlainConfig -> Network -> LLDP POE -> LLDP Send Max PoE.

10.3.0:C3
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.

10.3.0:C4
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.

10.3.0:C5
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.

10.3.0:C6
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.

10.3.0:C7
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.

10.3.0:C8
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel
scenarios.

10.3.0:C9
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.

10.3.0:C10
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

New features in 10.3.0
================================================================================

10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.

10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.

10.3.0:F3
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.

10.3.0:F4
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.

10.3.0:F5
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.

10.3.0:F6
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).

10.3.0:F7
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.

10.3.0:F8
Updated Video Motion Detection to version 4.4.9.

10.3.0:F9
Updated Motion Guard to version 2.2.8.

10.3.0:F10
Updated Fence Guard to version 2.2.8.

10.3.0:F11
Updated Loitering Guard to version 2.2.8.

Corrections in 10.3.0
================================================================================

10.3.0:C1
Corrected an issue that could cause live image to blink in dark conditions on
rare occasions.

10.3.0:C2
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.

10.3.0:C3
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.

10.3.0:C4
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.

10.3.0:C5
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.

10.3.0:C6
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.

10.3.0:C7
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.

10.3.0:C8
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.

This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.

Upgrade recommendations
========================

When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.

Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.

NOTE
========================

For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security

New features in 10.3.0
================================================================================

10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.

10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.

10.3.0:F3
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.

10.3.0:F4
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.

10.3.0:F5
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.

10.3.0:F6
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).

10.3.0:F7
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.

10.3.0:F8
Updated Video Motion Detection to version 4.4.9.

10.3.0:F9
Updated Motion Guard to version 2.2.8.

10.3.0:F10
Updated Fence Guard to version 2.2.8.

10.3.0:F11
Updated Loitering Guard to version 2.2.8.

Corrections in 10.3.0
================================================================================

10.3.0:C1
Corrected an issue that could cause live image to blink in dark conditions on
rare occasions.

10.3.0:C2
Added support for dynamic power allocation via Link Layer Discovery Protocol
(LLDP) in addition to PoE-class based power allocation. This allows the switch
to allocate less power to the camera and potentially a greater number of PoE
devices can be connected to the switch. LLDP can be enabled in Settings ->
System -> PlainConfig -> Network -> LLDP POE -> LLDP Send Max PoE.

10.3.0:C3
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.

10.3.0:C4
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.

10.3.0:C5
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.

10.3.0:C6
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.

10.3.0:C7
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.

10.3.0:C8
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel
scenarios.

10.3.0:C9
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.

10.3.0:C10
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.

AXIS M3106-L_Mk_II, version 9.80.3

AXIS M3106-LVE_Mk_II, version 9.80.3

AXIS M3046-V_1_8MM, version 9.80.3

AXIS M3045-WV, version 9.80.3

AXIS M3044-V, version 9.80.3

AXIS M2025-LE, version 9.80.3

AXIS Companion_Recorder, version 9.80.3

AXIS Companion_Eye_mini_L, version 9.80.3

AXIS Companion_Dome_mini_LE, version 9.80.3

AXIS Companion_Dome_WV, version 9.80.3

AXIS Companion_Dome_V, version 9.80.3

AXIS Companion_Cube_LW, version 9.80.3

AXIS Companion_Cube_L, version 9.80.3

AXIS Companion_Bullet_mini_LE, version 9.80.3

AXIS Companion_Bullet_LE, version 9.80.3

AXIS S3008, version 10.3.0

AXIS Q6135-LE, version 10.3.0

AXIS Q3515, version 10.3.0

AXIS Q1785, version 10.3.0

AXIS Q1700-LE, version 10.3.0