December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F3
Improved autofocus accuracy.
10.3.0:F4
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F5
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F6
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F7
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F8
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F9
Updated Video Motion Detection to version 4.4.9.
10.3.0:F10
Updated Motion Guard to version 2.2.8.
10.3.0:F11
Updated Fence Guard to version 2.2.8.
10.3.0:F12
Updated Loitering Guard to version 2.2.8.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Corrected a focus issue that occured after upgrade.
10.3.0:C2
Corrected an issue that could cause live image to blink in dark conditions on
rare occasions.
10.3.0:C3
Added support for dynamic power allocation via Link Layer Discovery Protocol
(LLDP) in addition to PoE-class based power allocation. This allows the switch
to allocate less power to the camera and potentially a greater number of PoE
devices can be connected to the switch. LLDP can be enabled in Settings ->
System -> PlainConfig -> Network -> LLDP POE -> LLDP Send Max PoE.
10.3.0:C4
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.
10.3.0:C5
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C6
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C7
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.
10.3.0:C8
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.
10.3.0:C9
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel
scenarios.
10.3.0:C10
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C11
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
Added support for live occupancy metrics and stateful events based on occupancy
thresholds.
10.3.0:F2
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F3
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F4
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F5
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F6
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F7
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F8
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F9
Updated Video Motion Detection to version 4.4.9.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Corrected an issue that could cause live image to blink in dark conditions on
rare occasions.
10.3.0:C2
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.
10.3.0:C3
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C4
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C5
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.
10.3.0:C6
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.
10.3.0:C7
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C8
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
↧
December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F3
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F4
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F5
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F6
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F7
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F8
Updated Video Motion Detection to version 4.4.9.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Added support for dynamic power allocation via Link Layer Discovery Protocol
(LLDP) in addition to PoE-class based power allocation. This allows the switch
to allocate less power to the camera and potentially a greater number of PoE
devices can be connected to the switch. LLDP can be enabled in Settings ->
System -> PlainConfig -> Network -> LLDP POE -> LLDP Send Max PoE.
10.3.0:C2
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.
10.3.0:C3
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C4
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C5
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.
10.3.0:C6
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.
10.3.0:C7
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C8
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F3
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F4
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F5
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F6
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F7
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F8
Corrected an issue that caused the audio transfer over HTTPS to not work
properly and with that, the audio-gain-level behavior was also reverted back to
the state it was known in AXIS OS releases up to AXIS OS 10.0.2. It is therefore
mandatory to upgrade to AXIS OS 10.3 when experiencing audio-related issues on
Axis devices running on AXIS OS 10.1 and 10.2. Upon release of AXIS OS 10.3,
AXIS OS 10.1 and 10.2 will be made unavailable for download from www.axis.com
moving forward.
10.3.0:F9
Updated Video Motion Detection to version 4.4.9.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Corrected an issue that could cause live image to blink in dark conditions on
rare occasions.
10.3.0:C2
Added support for dynamic power allocation via Link Layer Discovery Protocol
(LLDP) in addition to PoE-class based power allocation. This allows the switch
to allocate less power to the camera and potentially a greater number of PoE
devices can be connected to the switch. LLDP can be enabled in Settings ->
System -> PlainConfig -> Network -> LLDP POE -> LLDP Send Max PoE.
10.3.0:C3
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.
10.3.0:C4
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C5
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C6
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.
10.3.0:C7
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.
10.3.0:C8
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel
scenarios.
10.3.0:C9
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C10
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F3
Improved autofocus accuracy.
10.3.0:F4
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F5
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F6
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F7
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F8
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F9
Updated Video Motion Detection to version 4.4.9.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Corrected an issue that could cause live image to blink in dark conditions on
rare occasions.
10.3.0:C2
Added support for dynamic power allocation via Link Layer Discovery Protocol
(LLDP) in addition to PoE-class based power allocation. This allows the switch
to allocate less power to the camera and potentially a greater number of PoE
devices can be connected to the switch. LLDP can be enabled in Settings ->
System -> PlainConfig -> Network -> LLDP POE -> LLDP Send Max PoE.
10.3.0:C3
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.
10.3.0:C4
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C5
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C6
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.
10.3.0:C7
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.
10.3.0:C8
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C9
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
↧
December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F3
Improved autofocus accuracy.
10.3.0:F4
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F5
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F6
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F7
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F8
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F9
Updated Video Motion Detection to version 4.4.9.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Corrected an issue that could cause live image to blink in dark conditions on
rare occasions.
10.3.0:C2
Added support for dynamic power allocation via Link Layer Discovery Protocol
(LLDP) in addition to PoE-class based power allocation. This allows the switch
to allocate less power to the camera and potentially a greater number of PoE
devices can be connected to the switch. LLDP can be enabled in Settings ->
System -> PlainConfig -> Network -> LLDP POE -> LLDP Send Max PoE.
10.3.0:C3
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.
10.3.0:C4
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C5
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C6
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.
10.3.0:C7
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.
10.3.0:C8
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C9
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F3
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F4
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F5
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F6
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F7
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F8
Corrected an issue that caused the audio transfer over HTTPS to not work
properly and with that, the audio-gain-level behavior was also reverted back to
the state it was known in AXIS OS releases up to AXIS OS 10.0.2. It is therefore
mandatory to upgrade to AXIS OS 10.3 when experiencing audio-related issues on
Axis devices running on AXIS OS 10.1 and 10.2. Upon release of AXIS OS 10.3,
AXIS OS 10.1 and 10.2 will be made unavailable for download from www.axis.com
moving forward.
10.3.0:F9
Updated Video Motion Detection to version 4.4.9.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Corrected an issue where overlays sometimes could be placed incorrectly in the
video stream.
10.3.0:C2
Added support for dynamic power allocation via Link Layer Discovery Protocol
(LLDP) in addition to PoE-class based power allocation. This allows the switch
to allocate less power to the camera and potentially a greater number of PoE
devices can be connected to the switch. LLDP can be enabled in Settings ->
System -> PlainConfig -> Network -> LLDP POE -> LLDP Send Max PoE.
10.3.0:C3
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C4
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C5
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel
scenarios.
10.3.0:C6
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C7
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F3
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F4
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F5
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F6
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F7
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F8
Corrected an issue that caused the audio transfer over HTTPS to not work
properly and with that, the audio-gain-level behavior was also reverted back to
the state it was known in AXIS OS releases up to AXIS OS 10.0.2. It is therefore
mandatory to upgrade to AXIS OS 10.3 when experiencing audio-related issues on
Axis devices running on AXIS OS 10.1 and 10.2. Upon release of AXIS OS 10.3,
AXIS OS 10.1 and 10.2 will be made unavailable for download from www.axis.com
moving forward.
10.3.0:F9
Updated Video Motion Detection to version 4.4.9.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Corrected an issue where overlays sometimes could be placed incorrectly in the
video stream.
10.3.0:C2
Added support for dynamic power allocation via Link Layer Discovery Protocol
(LLDP) in addition to PoE-class based power allocation. This allows the switch
to allocate less power to the camera and potentially a greater number of PoE
devices can be connected to the switch. LLDP can be enabled in Settings ->
System -> PlainConfig -> Network -> LLDP POE -> LLDP Send Max PoE.
10.3.0:C3
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C4
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C5
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel
scenarios.
10.3.0:C6
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C7
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F3
Added installation feature âQuad and 360 viewâ for newer fisheye-cameras.
10.3.0:F4
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F5
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F6
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F7
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F8
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F9
Corrected an issue that caused the audio transfer over HTTPS to not work
properly and with that, the audio-gain-level behavior was also reverted back to
the state it was known in AXIS OS releases up to AXIS OS 10.0.2. It is therefore
mandatory to upgrade to AXIS OS 10.3 when experiencing audio-related issues on
Axis devices running on AXIS OS 10.1 and 10.2. Upon release of AXIS OS 10.3,
AXIS OS 10.1 and 10.2 will be made unavailable for download from www.axis.com
moving forward.
10.3.0:F10
Updated Video Motion Detection to version 4.4.9.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Corrected an issue that could cause live image to blink in dark conditions on
rare occasions.
10.3.0:C2
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.
10.3.0:C3
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C4
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C5
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.
10.3.0:C6
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.
10.3.0:C7
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel
scenarios.
10.3.0:C8
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C9
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
↧
December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F3
Added installation feature âQuad and 360 viewâ for newer fisheye-cameras.
10.3.0:F4
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F5
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F6
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F7
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F8
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F9
Corrected an issue that caused the audio transfer over HTTPS to not work
properly and with that, the audio-gain-level behavior was also reverted back to
the state it was known in AXIS OS releases up to AXIS OS 10.0.2. It is therefore
mandatory to upgrade to AXIS OS 10.3 when experiencing audio-related issues on
Axis devices running on AXIS OS 10.1 and 10.2. Upon release of AXIS OS 10.3,
AXIS OS 10.1 and 10.2 will be made unavailable for download from www.axis.com
moving forward.
10.3.0:F10
Updated Video Motion Detection to version 4.4.9.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Corrected an issue that could cause live image to blink in dark conditions on
rare occasions.
10.3.0:C2
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.
10.3.0:C3
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C4
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C5
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.
10.3.0:C6
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.
10.3.0:C7
Improved video streaming stability in multi-stream- and ONVIF Audio Backchannel
scenarios.
10.3.0:C8
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C9
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
December 21, 2020, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0
================================================================================
10.3.0:F1
MQTT is now activated by default upon power loss or reboot if MQTT was enabled
prior to it.
10.3.0:F2
Trigger Data functionality has been removed. Support for Trigger Data will
continue on 9.80 LTS.
10.3.0:F3
Corrected an issue that prevented setting the gain individually on the left and
right channel on products with stereo audio input.
10.3.0:F4
Added possibility to set a wear level for the SD card that the event system can
trigger on. This is set in the Storage page.
10.3.0:F5
SD card wear level is now displayed on the Storage page if the SD card supports
this feature.
10.3.0:F6
Added support for audit logging when a user exports video from the device's edge
recording (SD card, network share).
10.3.0:F7
Updated OpenSSL to version 1.1.1h to increase overall minimum cyber security
level.
10.3.0:F8
Updated Video Motion Detection to version 4.4.9.
Corrections in 10.3.0
================================================================================
10.3.0:C1
Corrected an issue that caused video clients to not display a low-FPS video
stream due to missing base FPS info in VUI timing info.
10.3.0:C2
Corrected an issue that caused PKCS#12-formatted certificate uploads to fail
when certain special characters were used as a password.
10.3.0:C3
Corrected text for time offset in the Date & Time web page, the offset is now
shown in milliseconds instead of seconds.
10.3.0:C4
Corrected an issue with pause-frame handling that could cause network
disconnections if pause-frames were enabled and used in the network.
10.3.0:C5
Corrected an issue that prevented the device to utilize the available network
bandwidth in high-latency networks such as 4G cellular network.
10.3.0:C6
Corrected an issue that caused the value of Quality of Service (QoS) to not be
respected in always multicast mode.
10.3.0:C7
Corrected an issue that prevented the device to stream in always-multicast mode
after the video stream processing has been restarted.
↧
January 10, 2021, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0.1
================================================================================
10.3.0.1:F1
Products with HardwareID 90F.1 and 90F.2 only support firmware 10.3.0.1 and
later.
Products with HardwareID 79E.1 and 79E.2 support all firmware versions.
The HardwareID can be found in Plain config -> Properties -> System ->
HardwareID
For more information, see https://www.axis.com/support/faq/FAQ116511
↧
January 10, 2021, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0.1
================================================================================
10.3.0.1:F1
Products with HardwareID 90F.1 and 90F.2 only support firmware 10.3.0.1 and
later.
Products with HardwareID 79E.1 and 79E.2 support all firmware versions.
The HardwareID can be found in Plain config -> Properties -> System ->
HardwareID
For more information, see https://www.axis.com/support/faq/FAQ116511
↧
↧
January 10, 2021, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0.1
================================================================================
10.3.0.1:F1
Products with HardwareID 910.1 and 910.2 only support firmware 10.3.0.1 and
later.
Products with HardwareID 79F.1 and 79F.2 support all firmware versions.
The HardwareID can be found in Plain config -> Properties -> System ->
HardwareID
For more information, see https://www.axis.com/support/faq/FAQ116511
↧
January 10, 2021, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
New features in 10.3.0.1
================================================================================
10.3.0.1:F1
Products with HardwareID 924.2, 924 and 925 only supports firmware 10.3.0.1 and
later.
Products with HardwareID 7A7.2, 7A7 and 7A8 supports all firmware versions.
The HardwareID can be found in Plain config -> Properties -> System ->
HardwareID
https://www.axis.com/support/faq/FAQ116512
↧
January 14, 2021, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
Corrections in 10.3.0.2
================================================================================
10.3.0.2:C1
Corrected an issue that sometimes made the IR-led not work as expected.
↧
January 18, 2021, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Upgrade recommendations
========================
When updating the device, it is recommended to do an intermediate upgrade
using an available AXIS OS LTS-release on the way to the desired AXIS OS
version.
For example, if the device currently is running AXIS OS 7.40 and you want to
upgrade to the latest AXIS OS Active Track (Example: 10.1, October 2020) then
you should do the upgrade in these steps: 7.40 => 8.40 LTS => 9.80 LTS => 10.1.
More detailed recommendations can be found in the AXIS OS portal at
https://www.axis.com/support/firmware.
Upgrade the firmware according to the instructions given in howtoupgrade.txt,
which is included in the firmware folder or according to instructions at
https://www.axis.com/support/firmware.
NOTE
========================
For latest information about Axis Cybersecurity, see:
https://www.axis.com/support/product-security
Release 10.3.0
========================
This is the first official Release for Q8752-E.
↧
↧
January 19, 2021, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Corrections
=====================
6.54.3556
Fixed - Unable to remove the new interface vlan in WEB UI.
6.54.3556
Fixed - Switch will reboot when receiving LLDP packet with 6 management addresses.
6.54.3556
Fixed - The modified hostname can not be kept after the switch restart.
6.54.3556
Fixed - The Trap Event Group Name is not displayed in running-config.
↧
January 19, 2021, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Corrections
=====================
6.54.3556
Fixed - Unable to remove the new interface vlan in WEB UI.
6.54.3556
Fixed - Switch will reboot when receiving LLDP packet with 6 management addresses.
6.54.3556
Fixed - The modified hostname can not be kept after the switch restart.
6.54.3556
Fixed - The Trap Event Group Name is not displayed in running-config.
↧
January 19, 2021, 3:00 pm
This firmware is now available. Please visit the product's support page on www.axis.com for the download, full release notes and installation instructions.
Corrections
=====================
6.54.3556
Fixed - Unable to remove the new interface vlan in WEB UI.
6.54.3556
Fixed - Switch will reboot when receiving LLDP packet with 6 management addresses.
6.54.3556
Fixed - The modified hostname can not be kept after the switch restart.
6.54.3556
Fixed - The Trap Event Group Name is not displayed in running-config.
↧